Control-company 1035 COUNTDOWN STOPWATCH Manuel d'utilisateur télécharger pdf

SPECIFICATIONS

Stopwatch—

Timing capacity: 9 hr, 59 min, 59 sec, 99/100

Resolution: 1/100

Countdown—

Timing capacity: 99 hr, 59 min, 59 sec

Resolution: 1 second

ENTERING TIMING MODES

Repeatedly pressing the MODE button toggles through the different timing modes

available. The position of the solid bar at the bottom of the display, appearing above

the captions, indicates the current mode.

STPW = Stopwatch mode

AUTO = Auto-Repeat Countdown Timer

DUAL = Dual Display

PACE = Pacer

1-60 = Pre-set Countdown Timer (rotary switch)

Example:

STPW AUTO DUAL PACE

1-60

The solid bar above “PACE” indicates the unit is in the Pacer mode.

NOTE: Modes may not be used simultaneously. In order to switch modes using the

MODE button, the mode being displayed must not be running and must be reset. To

reset any timing mode, timing must be stopped and then the SPLIT/RESET button

must be pressed.

STPW - STOPWATCH - Single Action Timing

1. Press the MODE button to select the stopwatch mode (STPW).

2. Press the SPLIT/RESET button to clear the display.

3. Press the START/STOP button to begin timing.

4. Press the START/STOP button to stop timing.

5. Press the SPLIT/RESET button to clear the displayand reset the stopwatch.

STPW - STOPWATCH - Time In/Time Out Timing

1. Press the MODE button to select the stopwatch mode (STPW).

2. Press the SPLIT/RESET button to clear the display.

3. Press the START/STOP button to begin timing.

4. Press the START/STOP button to stop timing. The timer holds the reading where it

was stopped (Time-Out). The upper display will “freeze” showing the Interval time.

The lower display will “freeze” showing the cumulative time.

Each press of the START/STOP button will increment the number that appears in the

“COUNT” box. The stopwatch stores into memory the last 8 Time-Out times.

These times can be re-called after timing hasbeen completed.

5. Press the START/STOP button to resume timing from the point that it was stopped

(Time-In). The upper display will show the time interval since the most recent press of

the START/STOP button. The lower display will show the current running time.

Any number of Time-Outs may be taken.

6. Press the START/STOP button to stop timing.

7. To recall the last 8 Time-Out times, press the RECL ∆ button. Each press of the

RECL ∆ button will cycle the display through the Time-Out times that have been

stored into memory.

8. Press the SPLIT/RESET button to clear the display and reset the stopwatch.

Pressing the SPLIT/RESET button also clears the times from memory.

STPW - STOPWATCH - Cumulative Split / Lap Interval

Cumulative Split Timing freezes the display for partial cumulative event times while the

internal clock continues to run. Each press of the SPLIT/RESET button displays the

total cumulative time since the START/STOP button was pressed.

Lap Interval Timing yields a readout of each individual time increment of a connected

series of events. Each press of the SPLIT/RESET button displays the time interval

since the previous press of the SPLIT/RESET button.

Interval time appears on the upper display, Cumulative time appears on the lower

display.

1. Press the MODE button to select the stopwatch mode (STPW).

2. Press the SPLIT/RESET button to clear the display.

3. Press the START/STOP button to begin timing.

4. Press the SPLIT/RESET button to take a Cumulative/Interval time. The upper

display will “freeze” showing the Interval time. The lower display will “freeze” showing

the cumulative time. After 5 seconds, the display will return to the current running

Interval and Cumulative time.

Each press of the SPLIT/RESET button will increment the number that appears in

the “COUNT” box at the upper left corner of the display.

Any number of Cumulative/Interval times may be taken. The stopwatch stores into

memory the last 8 Cumulative/Interval times. These times can be re-called after timing

has been completed.

5. Press the START/STOP button to stop timing.

6. To recall the last 8 Cumulative/Interval times, press the RECL ∆ button. Each

press of the RECL ∆ button will cycle the display through the Cumulative/ Interval

times that have been stored into memory.

7. Press the SPLIT/RESET button to clear the display and reset the stopwatch.

Pressing the SPLIT/RESETbutton also clears the times from memory.

AUTO - AUTO REPEAT COUNTDOWN

The Auto Repeat Countdown mode allows a countdown time to be programmed into

the timer. Once programmed and started, the timer will countdown and alarm when

zero is reached. The timer then returns to the programmed countdown time and starts

counting down again and will alarm again once zero is reached. This operation will

continue until stopped.

1. Press the MODE button to select the Auto Repeat Countdown mode (AUTO).

2. Press the SET button to enter the setting mode.

3. To set the desired time, press the SPLIT/RESET button to advance the hours,

press the RECL ∆ button to advance the minutes, press the START/STOP button to

advance the seconds.

4. Once the desired countdown time appears on the display, press the SET button.

5. Press the START/STOP button to begin timing.

6. If a pause in the timing operation is required, press the START/STOP button to

“freeze” the display at the current reading (time-out). To resume time at the point it

was stopped, press the START/STOP button again (time-in). An unlimited number of

time-outs may be taken.

To display the total elapsed time since beginning the countdown repeat operation,

press the RECL ∆ button. To return to the current countdown time, press the RECL ∆

button.

7. Once the display reaches zero, the timer will beep, return to the countdown time

and begin counting down. The number that appears in the “COUNT” box will be

increased by 1 up to 99.

8. Once timing has been completed, press the START/STOP button.

9. Press the SPLIT/RESET button to clear the display to the programmed countdown

time and reset the timer.

TRACEABLE

COUNTDOWN STOPWATCH INSTRUCTIONS

1 2 3

TRACEABLE 1
CONTROL COMPANY 3

Résumé du contenu

Page 1 - TRACEABLE

SPECIFICATIONS Stopwatch— Timing capacity: 9 hr, 59 min, 59 sec, 99/100 Resolution: 1/100 Countdown— Timing capacity: 99 hr, 59 min, 59 sec Resol

Page 2

DUAL - DUAL DISPLAY TIMER The dual display timer mode can be used in three ways: SU - Two countdown alarm timers working simultaneously. Id - Two coun

Page 3 - CONTROL COMPANY

BATTERY REPLACEMENT An incorrect display, no display or operational difficulties indicate that the battery should be replaced. Use a coin to open the

Commentaires sur ces manuels

Pas de commentaire

Control-company 1035 COUNTDOWN STOPWATCH Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Instruments de mesure Control-company 1035 COUNTDOWN STOPWATCH. Control Company 1035 COUNTDOWN STOPWATCH User Manual [it] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de mesure Control-company 1035 COUNTDOWN STOPWATCH